A Vast Improvement Over Existing Boarding Ladder and Swim Platform Designs!

	1 1/4" to 1/2" 304 Marine Grade Stainless Steel Construction Durable 1" thick plastic stair tread Comfortable 1 1/4" wide steps Large 15" X 16" underwater platform (patent pending) at bottom of ladder (15" X 12" on 12" ladders) Our patent pending QuickTrieve return system brings it out of the water with the pull of a handle Available in 2, 3, or 4 step designs Will support 250lbs as long as you have a solid backing plate mount to your boat
	Our patent pending "Click Slide" system provide quick deploying and retriving of the underwater platform Heavy nylon bushing ensure smooth, reliable and long lasting support bracket operation
	Stows in a compact 16" X 16" space (12" X 16" space for 12" ladders) Stows flush on the deck in just 2" of space (undermount bracket available)

Specification		16	12
A-	Stored Length:	16"	15"
B-	Stored Width (pipe outside edges):	15.5"	11.5"
C-	Stored Width (outside slides):	16.5"	12.5"
D-	Stored Height:	2 3/4"	2 3/4"
E-	Mounting Bracket Length:	6"	6"
F-	Mounting Bracket Width:	1 3/8"	1 3/8"
GHI-	Deployed Length:	~23" ~34" ~45"	~23" ~34" ~45"
J-	Mounting Bracket Holes (lenthwise):	1/2" and 2" from inside edge	1/2" and 2" from inside edge
K-	Mounting Bracket Holes (widthwise):	14 1/4"	10 1/4"
L-	Setback from Edge:	5"	5"

(Click on any image to enlarge it.)

Select a mounting location that will provide a strong, solid and reliable surface. Avoid weak areas or uneven surfaces. Ensure that when deployed, there is adequate clearance between propellers and other dangerous items.

Place the product in the desired mounting location with the brackets attached and mark the position of the mounting brackets.

Once the brackets have been marked, remove the product and mark each of the mounting brackets two holes.

The telescoping functionality of the product may bind excessively if the mounting brackets are not installed in a parallel fashion. Before drilling any mounting holes, place the product into its proposed location and ensure that its range of motion necessary for deployment and retrieval is not impeded by any boat surface or structure.

Drill a 1/4" hole for each of the marked mounting bracket holes.

The product should be mounted with 1/4" diameter stainless steel bolts. The bolts should have large washers or a backing plate to help to distribute the load incurred when the product is fully deployed.

Tighten the bolts, making sure the mounting brackets are firmly attached to the mounting surface.

Finally, insert the 1/4" bolt through each arm of the unit. Make sure to check and finalize all installations prior to deploying, retrieving, or climbing on the product.

If your mounting surface is unique, please contact us or send a digital picture. We may have some ideas or have solved the same problem for someone else already!

**For dimensions see the "Dimensions" link to the right.

Disclaimer: This ladder platform can be dangerous and cause bodily harm if not installed or operated correctly.

(Click on any image below to enlarge it.)

To deploy, lift the stair platform off the deck surface. Rotate the stair platform on its mounting brackets until vertical.

Push the stair platform past vertical toward the water and release to let it sink into the water.

The momentum of this action as well as gravity will fully extend the stair platform. Take the stair and place the stud side to the right. Insert the stud into the mounting hole on the Click Slide bracket. Line up the hole in the stair and the Click Slide bracket on the left side of the stair platform. Take the QuickTrieve pin and push it through these holes, securing the stair in place.

The stair platform is now deployed and ready to use.

To retrieve the platform, pull the QuickTrieve handle- the stair pin will release and the stair will align with the QuickTrieve rope.

Continue pulling on the QuickTrieve handle to lift the stair platform out of the water until it is vertical.

Fold the stair platform flat and the Click Slide brackets will fold into their storage position.

Be careful not to place hands or fingers in between the ladder platform and the Click Slide brackets or they may get caught. Lay the stair platform flush on the deck.

Slide the QuickTrieve handle inside the round wire connector to the QuickTrieve pin with the pin parallel to the handle about 1/2 in. from the end of the handle. Turn the QuickTrive pin to the vertical position so it will grasp the QuickTrieve handle. Place the stair on top of the inner tread and align the hole in the left side of the stair with the storage hole in the base of the stair platform. Insert the QuickTrieve pin through the stair into the storage hole.

Disclaimer: This ladder platform can be dangerous and cause bodily harm if not installed or operated correctly.

The ladder platform is designed and manufactured to require little maintenance; however, a few simple items will extend the life of your product:

• Periodic washing off with fresh water, both inside and out
• Periodic lubrication of the telescoping arms using silicone or similar substance (thoroughly spray into the hole in the bottom and top caps)
• Wipe down the product from time to time to remove dirt and grime
• Periodic polishing with a stainless steel polish for marine applications
• Periodic inspection of the mounting brackets for safety and deterioration of the mounting surface

Safety Tips:

• Keep fingers and toes clear of click slide brackets and studs as well as telescoping arms.
• Do not jump on the ladder, or dive from the ladder.
• Step in the center of ladder steps.
• Only one person should ascend the ladder at a time.
• Face the ladder when ascending or descending.
• Do not use the ladder while engine is running.

Disclaimer: This ladder platform can be dangerous and cause bodily harm if not installed or operated correctly.

The Ladder Platform in Action:

(Click on any image below to enlarge it.)

Relaxing on the back of the boat, a comfy seat.	A chat and a drink.	Video Coming Soon.
Ready to go snorkeling.	Standing up.